        
New Arrivals
Inventory |
|
Item # |
DESCRIPTION |
|
35319p- |
Tri
Clover, Tri Blender model F4329MD, 316 stainless steel, 20 HP drive,
3/60/230/460/3510 RPM TEFC motor, V belt drive, 2" inlet, 3" outlet,
tri clamp fittings, dry ingredients capacity up to 350 pound per
minute, stainless steel base |
|
8230p- |
Tri
Clover, Tri Blender model F4329MD, 20 HP, 4" inlet, funnel, mounted
on stainless steel base |
|
44762p- |
Tri
Clover, Tri Blender model F4329MD, 20 HP, 2" inlet 3" outlet mounted
on mild steel base 32" x 20" floor space required 230/460 volt 3
phase |
|
52966p- |
Tri
Clover, Tri Blender model F3218MEDB40, stainless steel contact, 10
HP, model 48463110IEB electric control panel, electric operated
stainless steel butterfly valve on feed |
|
52965p- |
Tri
Clover, Tri Blender model F3218MEB60, stainless steel contact, 15 HP |
|
52964p- |
Tri
Clover, Tri Blender model F3218MDS, stainless steel product contact,
15 HP |
|
41393- |
Tri
Clover, Tri Blender model F3218MD-B60, 20 HP 3525 RPM 230/460 volt,
mild steel frame, 1.5" tri clamp inlet, 2" tri clamp outlet, belt
driven, FR256T |
|
53486p- |
Tri
Clover, Tri Blender model F3218MD, 20 HP 3/60/230/460/3540 RPM TEFC
motor, 316 stainless steel, V Belt drive, 1.5" inlet 2" outlet with
Tri clamp fittings, dry ingredients capacity up to 100 pounds per
minute, mounted on stainless steel base overall size; 20" x 30" x
32" high |
|
43285p- |
Tri
Clover, Tri Blender model F3218MD, 10 HP, 18" diameter x 29" deep
powder funnel 1.5" inlet 2" outlet mounted on mild steel base with
casters 32" x 20" floor space required 60" overall height, 230/460
volt |
|
50682p- |
Tri
Clover, Tri Blender model F3218, 10 HP, no circulator pump included. |
|
48321p- |
Tri
Clover, Tri Blender model F2116MDB40, 2" in & 1.5" out, stainless
steel contact, 2.5 HP 3600 RPM motor 230/460 volt 3 phase with
hopper |
|
43973- |
Tri
Clover, Tri Blender model DS3218MDGMBVS, 30 HP, up to 100 pounds per
minute, dual stage, portable |
|
47097- |
Tri
Clover, Blender model F2116MD, 316 stainless steel, 2.5 HP |
|
47317p- |
Strong
Scott, Blender model TJS14B, stainless steel construction, equipped
with 20 HP Reeves drive, half jacketed rated 150 PSI at 650º F,
mixing chamber is 14" diameter x 40" long, paddled rotor turns at a
maximum of 2400 RPM, 4" x 10" top in feed & bottom discharge, 6.5" x
34.5" access door, requires 230/460 vac 3 phase electrical supply |
|
51045p- |
Ribbon
Blender, carbon steel ribbon with ceramic lower section, lined &
wooden top half, 17.25" wide x 38.5" x 19" deep, 3" side bottom
discharge, mounted on 4 legs, allowing 22" discharge height, has
wooden cover & brush sifter/feeder (requires drive) |
|
53537p- |
Powder
Blender/Mixer, stainless steel, consisting of powder funnel with 2"
clamp connections, incline stainless steel dry ingredients table,
pump mounting plate all mounted on stainless steel tubular floor
stand with adjustable ball feet, various pumps available at an
additional charge |
|
54083p- |
Marion/Mueller, Paddle Blender model T6239, stainless steel
jacketed, 12" x 4-1/2', 125 PSI dimple jacket with National Board
#6626, 6" end bottom discharge, polished welds, Dodge shaft mounted
gear reducer size TDT425 S/N 6212, 24.64 ratio, no tag on motor but
looks like 5 HP |
|
54082p- |
Marion/Mueller, Paddle Blender model T6239, stainless steel
jacketed, 12' x 4-1/2', 125 PSI dimple jacket with National Board
#5757, 6" end bottom discharge, 7.5 HP motor 230/460 volt 1765 RPM
with vari speed pulley to Dodge shaft mounted gear reducer size
TXT425AS, 24.38 ratio |
|
48320p- |
Lightnin,
Liquid Blender model B77R0067NSQ, .43 HP 1725 RPM 220/440 volt 3
phase, two 3-1/2" diameter props |
|
53340p- |
Intensifier Bar for Patterson Kelley 30 cubic foot twin shell
blender, 60" bar length with all stainless steel construction &
spring loaded stub shaft for mounting, bar surface shows some
staining, former application unknown |
|
55068p- |
Greerco,
Emulsifier model 6H79, high sheer, mixer driven by 20/10 HP
3540/1770 RPM electric motor, requires 440 vac 3 phase electric
supply |
|
53653- |
Dual Auger
Blender, all stainless steel, 8" diameter x 64" long augers, 24" x
24" flanged top opening, 10" x 10" square discharge ports at end of
each auger, bottom opening doors under each auger, with 2 Bunting
magnets that bolt to the 10" x 10" openings, Bunting magnet
enclosures have hinged doors for easy access |
|
55003- |
Doyle
Roth, Blender, maximum working pressure 150 PSI & full vacuum, 60
PSI jacket, National Board #4659, stainless steel product contact, 1
HP variable speed motor on agitator, 13" bowl diameter x 21" deep |
|
53145- |
Double
Ribbon Blender model 09182, single shell |
|
54093p- |
Continuous
Twin Screw Blender, stainless steel, 39" wide x 138" long with (2)
18" diameter mixing auger, 39" x 19" end bottom outlet, 7.5 HP gear
head motor drive, previously used to blend a pressing agent with
apple pulp |
|
54097p- |
Buffalo,
Blender, mild steel frame, manual tilt bowl, 15 HP drive, mild steel
paddles, stainless steel clad bowl, twin shaft |
|
47260p- |
Bohle, Lab
Blender model LM40, aerator with two stainless steel blending
containers, one stainless steel lab car, mobile laboratory scale
blender, NIR spectrometer integrated into the lid of the blending
bin, specially adapted 21 CFR Part 11 compliant software, housed
with light source in a single steel box that rotates with bin,
continuous 24 V DC power through slip ring technology eliminates
batteries, data transferred using wire cables instead of radio
signals to eliminate possible interference, blender is integrated
into frame with lock casters, Plexiglas cover protects blending
container, which is available in 4 standard sizes of 5L, 10L, 20L &
40L |
|
31332- |
All
stainless steel insulated product Blender, designed for addition of
liquid carbon dioxide, or nitrogen to product, insulated chamber is
4' 6" long x 21" wide x 26" deep, with single piece lift cover,
rotary star valve discharge, stainless steel single shaft mixing
paddle, unit is 6' 6" high on mild steel frame. |
|
47134p- |
6,000
pound Blentec, CO2 Paddle Blender model DM34072PV, unit is bottom
injected with 6 ports on each side, includes lid with exhaust ports,
overall dimensions are 107" long x 82" wide x 126" high with lid
closed, currently set up for end pivot lid, lid is 79" long x 74"
wide, unit is missing 2 small diameter air cylinders which open 1 of
the discharge doors & 1 of the large diameter cylinders which open
the lid |
|
43044p- |
3,000
pound Reitz, Horizontal stainless steel Double Rotor Blender, 60
cubic foot |
|
12410- |
3,000
pound Powder Blender, carbon steel, 30 HP drive, 150" long x 52"
wide x 51" deep. |
|
47135p- |
1,500
pound Dual Shaft Ribbon Blender |
|
41251p- |
700 gallon
capacity CE Howard, Horizontal Paddle type Liquid Blender, stainless
steel construction, Hub City shaft mounted gear reducer with
hydraulic motor bottom slopes to 3" center outlet with ball valve 3
inner paddles 4" x 3/8" & 3 outer paddles 3" x 3/8", 42" x 84" x 50"
deep inside dimensions stainless steel construction |
|
38466p- |
700 gallon
capacity CE Howard, horizontal paddle Liquid Blender, Hub City shaft
mounted gear reducer with hydraulic motor bottom slopes to 3" center
outlet with ball valve 3 inner paddles 4" x 3/8" & 3 outer paddles
3" x 3/8", 42" x 84"x 50" inside dimensions, stainless steel
construction |
|
42981p- |
600 gallon
working capacity Walker, Single Ribbon Blender model SP6132,
hydraulic motor, 60" W x 85" L x 106" H, 25" diameter single ribbon,
6" diameter center bottom sanitary discharge, was blending thick
chunky salsa, can convert to electric drive at cost |
|
33761- |
240 cubic
foot Rietz, Blender, double auger stainless steel product, U shaped
blender with 2 augers & single ribbon, augers measure 30" diameter x
132" long, two 30 HP gear head motors, two 10" x 10" pneumatic
activated slide gate bottom outlets, 14' long x 8' wide x 11'6" high
overall measurements, includes stainless steel staircase |
|
22148p- |
225 gallon
Patterson Kelley, Twin Shell V Blender, maximum density of 55 pounds
per cubic foot, equipped with liquid solids bar, has 38" diameter
shells with two 18" diameter off floor, mild steel base, mounted on
30" pedestal stand, unit has epoxy coated interior with carbon steel
shell, 10 HP 3/60/208/230 drive. |
|
49531p- |
200 cubic
foot Double Ribbon Blender, stainless steel 120" long x 60" wide x
65" deep vessel, 16" square center bottom outlet with pneumatic
slide gate, double helix ribbon 60" diameter, 6" wide x .75" thick
ribbons, 5.5" diameter center shaft at exterior bearing, with
pneumatic shaft seals, stainless steel cover, Ortex pneumatic slide
gate, 50 HP 230/460 volt 3 phase constant speed drive motor coupled
to Falk gear reducer geared for 41 RPM at the ribbons |
|
53803p- |
200 cubic
foot capacity Hayes & Stolz, Double Ribbon Blender, insulated
product shell, heavy duty, food grade, 40 HP drive, 10 RPM at
ribbon, covered top with two 7" & two 25" square inlets, drive chain
& guards included, 64" wide x 120" long with 64" diameter spiral
double ribbon mixer approximate dimensions, off set bottom outlet
with MAC air lock included |
|
51554- |
160 cubic
foot Ross, Dual Ribbon Blender, stainless steel, sanitary polished
design, U shaped blending vessel with end discharge, 3 piece hinged
top cover with stainless steel breaker frame on top, product area
measures 98" long x 48" wide x 58" deep, dual blending ribbon is 48"
diameter & powered by 30 HP chain drive with Rexnord gear head speed
reducer, blender is mounted to a steel frame work platform measuring
90" wide x 16' long |
|
45814p- |
160 cubic
foot Ribbon Blender, 30 HP 3/60 230/460/1770 RPM motor, chamber &
ribbon stainless steel, 4-3/8" shaft at pillow block bearings,
bottom center 6" discharge, mixing chamber 143" long x 4' wide x 52"
deep, dual chain drive with 3' diameter sprocket, sentinel reducer,
ratio 29.70 to 1, double ribbons 1/2" thick x 2.5" wide, overall
size 16-1/2' long x 7' high without drive, not food grade. |
|
53804p- |
150 gallon
JH Day Littleford, Sigma Mixer/Blender, stainless steel food grade,
100 PSI at 350º jacket |
|
55005p- |
140 quart
Hobart, Vertical Blender model V1401, with 60 quart stainless steel
bowl & adapter, stainless steel paddle, 5 HP 220 volt 60 cycle 3
phase motor with 1 tub dolly |
|
55006p- |
140 quart
Hobart, Vertical Blender model V1401, 5 HP 220 volt 60 cycle 3 phase
motor, stainless steel bowl with stainless steel paddle & 1 tub
dolly |
|
44478p- |
125 cubic
foot Grace, Ribbon Blender, U shaped insulated blending tub measures
72" long x 53" wide x 57" deep, stainless steel lift covers heavy
duty blending blades are 4" wide on center shaft powered by a head
mount gear motor with chain drive to shaft approximate dimensions
are 10' long x 4' 6" wide x 8' high, size 6000 |
|
53050p- |
120 cubic
foot Rietz, Double Arm Blender model 60, insulated, all stainless
steel construction, 58" diameter x 81" long, approximately 60 cubic
foot working capacity, (4) 4" wide x 1/2" thick paddle bars which
run the full length of blender, hydraulic drive motor, (1) 4", (4)
2" bottom outlets with tri clamp connections, 3 piece removable top
covers, 96" overall height, 26" bottom clearance to floor, less
hydraulic power pack, USDA approved |
|
48128p- |
120 cubic
foot Ribbon Blender, 30 HP drive |
|
35690p- |
120 cubic
foot JH Day, carbon steel double Ribbon Blender, model 44x10, fully
jacketed, features 144 cubic foot (1080 gallon) total capacity, 44"
wide x 10' long x 52" deep mixing chamber, fully jacketed body (stay
bolt design), 4" center bottom outlet, requires drive between 25/40
HP, blender includes drive sprocket, formerly used in paint
manufacturing. |
|
47335p- |
120 cubic
foot Double Ribbon Blender, working capacity, stainless steel, 50"
diameter x 10' long x 59" deep, 48" discharge height, 30 HP drive,
mounted with belt pulley & on shaft reducer, standard package
glands, factory outboard bearings, 8" center bottom discharge, heavy
duty construction, 2.5" blade on ribbons, will accommodate up to 50
HP, full 1 piece cover |
|
35561p- |
110 cubic
foot Ribbon Blender, 20 HP drive, 43" wide x 10' long x 50" deep
chamber size, ribbons are 2.5" deep x 5/16" thick inner & outer,
center shaft 3-1/4" at bearings, 5-1/4" inside, 12" bottom center
discharge with 3" flange, 8" off floor, painted on the outside, both
frame & tub, 24" diameter drive sprocket with 20 HP 3/60/220/440
motor direct connect to Falk reducer, no cover, carbon steel frame,
overall 12' long x 5' high, stainless steel unit. Chemical grade
only |
|
52285p- |
106 cubic
foot Mueller, Double Ribbon Blender model RBS106, stainless steel
construction, 88" long x 48" wide x 48" deep, 9" diameter end bottom
discharge with 16" x 6" flap gate inspection door, 1-1/2" wide x
1/2" thick outer ribbon, 2-1/2" wide x 3/8" thick inner ribbon,
driven by 20 HP 230/460 volt 1760 RPM 3 phase 60 Hz motor & includes
vari speed controls, previously had center bottom discharge &
converted to end bottom discharge with pneumatic butterfly valve,
mounted on carbon steel legs |
|
44477p- |
100 cubic
foot Grace, Ribbon Blender, all stainless steel, U shaped insulated
blending tub measures 62" long x 53" wide x 57" deep inside, water
jacket on bottom, stainless steel lift covers, heavy duty blending
blades are 4" wide on center shaft, powered by a head mount gear
motor with chain drive to shaft, approximate dimensions are 9' long
x 4' 6" wide x 8' high, size 5,000 |
|
54133p- |
100 cubic
foot Double Ribbon Blender, stainless steel, 30 HP drive thru triple
chain & sprockets, 55" wide x 102" long, center discharge, requires
230/460 vac electrical supply |
|
47951p- |
100 cubic
feet capacity Boldt Industries, Ribbon Blender model BBV34P040,
stainless steel, dual solid flight stainless steel sanitary ribbons,
air operated end discharge doors, single piece dome cover, 80" wide
x 8' long x 6' high overall dimensions, cannot get close to take
good pictures, need forklift to move & take good pictures |
|
55004p- |
80 quart
Hobart, Vertical Blender model M802, stainless steel bowl, stainless
steel paddle, 2 HP 3 phase 60 cycle 220 volt motor with 1 tub dolly |
|
54905p- |
80 cubic
foot Ribbon Blender, jacketed with shroud, insulated, single ribbon,
40" wide x 92" long x 44" deep inside dimensions, chain & sprocket
drive to Dodge gear reducer, 1 piece full top hinged cover with 2
service ports, front is 24" x 26", rear is 12" x 24", start/stop, 5"
diameter center bottom slide gate discharge, sprocket safety covers,
mounted on short steel legs |
|
6890p- |
80 cubic
foot Grace, Ribbon Blender, stainless steel, U shaped insulated
blending tub measures 60" long x 54" wide x 55" deep, stainless
steel lift cover, heavy duty stainless steel blade mixers,
consisting of (4) 4" x 3" stainless steel bars on a horizontal
stainless steel shaft, 4" clamp bottom end outlet, overall
dimensions are 103" long x 60" wide x 7' 8" high, powered by 7½ HP
motor, with chain drive gear box, size 50 |
|
40929p- |
80 cubic
foot capacity Rietz, Product Blender model C12K7211, stainless
steel, U shaped body with single ribbon helical blender, equipped
with 12" diameter stainless steel bottom auger discharge includes
Crepaco size 6 HP rectangular inlet blending pump on stainless steel
frame with 30 HP motor, blending chamber is 9' long x 36" wide x 48"
deep, separate drive assemblies for blending ribbon & auger |
|
41244- |
80 cubic
foot capacity double ribbon Blender, stainless steel contact with
mild steel frame, 6" end bottom discharge with butterfly valve, 36"
wide x 8' long inside dimensions, inner ribbon is 3/8" x 2-7/8",
outer ribbon is 1-3/4" x 1/4", was used on liquid steam injected,
7.5 HP drive to a Falk gearbox |
|
41239p- |
80 cubic
foot capacity Aaron, double ribbon Blender, stainless steel, 40"
wide x 8' long inside dimensions stainless steel frame 1/2" x 2"
inner & outer ribbons 8" center bottom outlet with butterfly valve |
|
41240p- |
80 cubic
foot capacity Aaron, double ribbon Blender, stainless steel, 40"
wide x 8' long inside dimensions mild steel frame 1/2" x 2" inner &
outer ribbons 8" center bottom outlet with butterfly valve stainless
steel contact with mild steel frame 20 HP drive motor 460 volt 3
phase |
|
48649p- |
80 cubic
foot APV Crepaco, Blender model 80FB, USDA approved, 75 PSI jacket,
all wetted surfaces are constructed to T316 stainless steel, the
balance of the unit with the exception of the drive mechanism is
constructed T304 stainless steel, all welds are continuous, crack &
crevice free, domed cover, 15 HP wash down duty gear motor operating
at approximately 23 final RPM |
|
46136p- |
75 cubic
foot Patterson Kelley, stainless steel Twin Shell Blender, rated for
maximum material density of 60 pounds per cubic foot, powered by 7.5
HP motor, 230/460/3 phase voltage, 11/22 AMP at 1,750 RPM, motor
directly coupled to inline helical 17.1 to 1 gear reducer by Foot
Bros. yielding co shaft RPM of 102 & driving shell with standard
bull & spur gear arrangement, drive equipped with Warner electric
brake, mounted on painted carbon steel stand, 16.5" discharge, 17" &
24" discharge ports |
|
46132p- |
75 cubic
foot Patterson Kelley, stainless steel Twin Shell Blender, maximum
product density rating of 60 pounds per cubic foot, 7.5 HP shell
drive by Pacemaker motors, 208 volt/3 phase/23 AMP, 1750 RPM
directly coupled to foot Jones, helical, in-line, 17 to 1 gear
reducer yielding 10 CO shaft RPM & driven shell with standard bull &
spur gear at 25 RPM, drive is equipped with Warner brake, 16.5"
discharge, 24" & 17.5" charging ports, painted factory stand with
frame extension, 12' W x 60" x 10' H |
|
35691p- |
70 cubic
foot Hobart, double Ribbon Blender, model BL30, features all
stainless steel construction with food grade design, 8" diameter
bottom auger for mixing assist & discharging, 10 HP drive with in
line gear reducer, frame mounted with chain & sprocket drive, mixing
trough dimensions 47" wide x 86" long x 30" deep, full covers with
top safety dump grate, 50" discharge height, 230/460/3 phase
voltage, new electrical controls with reversing capability for
mixing & unloading cycle. |
|
41242p- |
65 cubic
foot capacity double ribbon Blender, 40 HP drive stainless steel
product contact mild steel frame 36" wide x 8' long 8" center bottom
discharge |
|
34501p- |
65 cubic
foot (486 gallon) Cooker/Blender, all stainless steel dual paddle, U
shaped jacketed product blending tub measures 15" long x 30½" wide x
28" deep, rated for 15 PSI steam or 45 PSI water, hinged single
piece cover with baffle, twin stainless steel blending paddles are
15" long with sanitary seals, dual 4" clamp outlets, two 1½" tri
clamp inlets on top of long side, offered with new 2 HP gear head
drives with chain sprockets & VFD speed controllers, heating
controls not included. |
|
41245p- |
64 cubic
foot double ribbon Blender, mild steel frame, 6" center bottom
outlet with butterfly valve, 38" wide x 96" long inside dimensions
inner ribbon 1/4" x 2-3/8", outer ribbon 1/2" x 1-1/4", was used for
liquid & steam injected 7.5 HP drive |
|
55008- |
60 cubic
foot Strong, Paddle Blender model 3061, 3' wide x 8' long, stainless
steel contact with mild steel frame, stainless steel covers & dust
collection hoods, out board bearings, bolted on paddles, center
discharge with slide gate, 3" diameter shaft, Dodge size TD7A shaft
mounted gear reducer, 20 HP motor 220/440 volt |
|
55009- |
60 cubic
foot Strong, Paddle Blender model 3061, 3' wide x 8' long, stainless
steel contact with mild steel frame, stainless steel covers & dust
collection hoods, out board bearings, bolted on paddles, center
discharge with slide gate, 3" diameter shaft, Dodge size TD7A shaft
mounted gear reducer, 20 HP motor 220/440 volt |
|
54335p- |
60 cubic
foot Patterson Kelley, V Blender, twin shell blender, stainless
steel construction, rated 50#/cubic foot maximum material density,
standard access ports with covers, 10" discharge, on stands with 33"
high stand extensions, 5 HP 230/460 volt shell drive |
|
42495p- |
60 cubic
foot Patterson Kelley, Twin Shell Dry Blender, stainless steel |
|
47509p- |
60 cubic
foot capacity Patterson Kelley, V Blender, stainless steel product
contact, 95 pound per cubic foot product density, liquid solids bar |
|
41241p- |
60 cubic
foot capacity Cleveland, double ribbon Blender, 36" wide x 7' long
inside dimensions inner ribbon is 5/8" x 2" outer ribbon is 5/8" x
1.5" Faulk gear box with 40 HP drive motor 6" diameter discharge
with valve, discharge is off center toward the drive end stainless
steel contact, preciously used on a lye based detergent |
|
35571p- |
50 cubic
foot Patterson Kelley, V Blender model 50, twin shell, carbon steel
& stainless steel, designed for material 55 pounds cubic foot or
lighter, 5 HP drive 3/60/208/203/220/1750/direct coupled to foot
reducer ratio 17:1 final 100 RPM to gear drive, discharge is 16"
butterfly valve that is 4' 7" from floor with support stands, 16"
top openings in shells with covers, has provisions for intensifier
bar no bar or bar drive, overall 130" wide x 54" deep x 12-1/2' high |
|
52805p- |
50 cubic
foot Patterson Kelley, V Blender model 50, stainless steel
construction, with bar, rated 55 pounds per cubic foot, includes
valve & leg extensions, 15 HP bar, 5 HP main drive 230-460v power |
|
43655- |
50 cubic
foot Patterson Kelley, V Blender model 50, stainless steel
construction with bar, rated 55 pound/cubic foot, includes valve &
leg extensions, 15 HP bar/5 HP main drive 230-460 volt power |
|
41294p- |
50 cubic
foot George R. Rogers Co, carbon steel ribbon/paddle Blender, mixing
trough dimensions 30" wide x 34" deep x 90" long 8" diameter center
bottom discharge with flanged connection 2 piece full covers with 2"
x 24" inspection ports with hinged covers 2.5" main shaft with
packing gland seals jack shaft drive arrangement with General
Electric 7-1/2 HP at 1750 RPM 220/440 volt 3 phase |
|
19089p- |
40 cubic
foot Will Flow, Paddle Blender, stainless steel, U shaped blending
tub measures 7' long x 41" wide x 48" high, center bridge with lift
covers, single shaft blending assembly with 4 sets of dual paddles,
jacket rated for 50 PSI at 300º WPI, 3" clamp bottom outlet,
National Board #2348 |
|
55071p- |
40 cubic
foot Scannell Boiler Works, Double Cone Blender model 40C7,
stainless steel, shell driven by 1 HP Reeves variable speed gear
motor with chain & sprockets, shell has 60" diameter x 20" straight
side with 20" cones, 12" flanged fitting on 1 cone & 16" hinged
access lid on the other, shell is constructed of 1/8" stainless
steel, supported by 3" carbon steel shafts, 11' wide x 8' deep x 8'
tall overall dimensions, requires 230/460 vac 3 phase power supply |
|
43652p- |
40 cubic
foot Patterson Kelley, V Blender, LS bar & drive, stainless V &
covers, with gear on gear main drive with reducer, mild steel
construction stand, rated 90 pound/cubic foot, 7.5 HP EXP 460V,
skidded for immediate delivery |
|
55007- |
40 cubic
foot Patterson Kelley, Twin Shell Dry Blender, maximum material
density 65 pound per cubic foot, stainless steel product contact,
mild steel frame, 10" diameter discharge with butterfly valve,
intensifier bar |
|
42786p- |
40 cubic
foot Patterson Kelley, Duplex Paddle Blender model 4204S.S., 15 HP
drive motor |
|
38462p- |
40 cubic
foot capacity Patterson Kelley, V Blender, maximum density 65 pounds
per cubic foot, stainless steel product contact, 5 HP 220/440 volt 3
phase motor direct connected to a Foote Brothers parallel shaft gear
box on the main drive, liquid addition intensifier bar driven by a
7.5 HP 220/440 volt 3 phase motor |
|
55002- |
36 cubic
foot capacity Double Ribbon Blender, low pressure dimple jacket,
stainless steel product contact & frame, mild steel out board
bearing mounts, 30" wide x 78" long, 3" shaft, 6" bottom outlet with
butterfly valve, 1/4" x 2" inner ribbon, 3/8" x 1-3/8" outer ribbon |
|
41248p- |
35 cubic
foot capacity Ribbon Blender stainless steel with a stainless steel
frame 6' long x 30" wide 1/4" x 2" inner & outer ribbons 7" end
bottom discharge with pneumatically operated butterfly valve shaft
mounted gear reducer 1750 RPM 220/440 volt 10 HP motor with starter
& disconnect. Manufacturer unknown |
|
46027p- |
30 cubic
foot stainless steel Twin Shell V Blender, shell is 30" diameter x
58" along side, shell is rotated by 3 HP motor, equipped with
stainless steel intensifier bar driven by 10 HP motor, unit is set
for liquid injection, supported on carbon steel stand, pneumatic
butterfly discharge valve, requires 230/460 vac 3 phase electric
power, last used for iron graphite with a density of 60 pounds/cubic
feet |
|
38459p- |
30 cubic
foot Patterson Kelley, V Blender, stainless steel product contact
liquid addition intensifier bar maximum product density 90 pounds
per cubic foot |
|
35694p- |
30 cubic
foot Patterson Kelley, stainless steel Twin Shell Blender, stainless
steel contact parts, rated for maximum product density of 190 pounds
per cubic foot, pin intensifier bar with 15 HP drive, 7.5 HP main
drive, all drives 220/440/3 phase voltage bull & spur gear shell
drive, mounted on painted carbon steel stand, measures 48" wide x
10' x 112" high, weighs 3,500 pounds. |
|
42591p- |
30 cubic
foot Patterson Kelley, stainless steel sanitary Blender, twin shell
solids, capacity rating of 55 pounds per cubic foot maximum product
density, 10" discharge with Patterson Kelley solids flow manually
operated butterfly valve, externally polished shell with factory
painted steel frame, formerly used in food ingredients manufacturing |
|
54132p- |
30 cubic
foot Lowe, Paddle Blender, stainless steel, 36" diameter x 48" long
paddle mixer, paddles driven by hydraulic power motor, 3" sanitary
center discharge, unit on 4 stainless steel legs, 82" long x 39"
wide x 57" high overall dimensions |
|
44465p- |
30 cubic
foot Gemco, Double Cone Blender, constructed of stainless steel,
fitted with a pneumatically operated discharge valve & cylinders to
hold a 55 gallon drum in place while loading, feed opening is 18"
diameter, blending chamber is 52" diameter x 15" straight side with
18" cones, equipped with 7.5 HP high speed intensifier bar, unit is
mounted on steel channel stands & driven by 10 HP 230/460 volt 3
phase gear motor |
|
47190p- |
30 cubic
foot Gemco, Double Cone (conical) Blender/Processor, model
formulator, standard clamp type charge cover, automatic pneumatic
discharge valve, shell is jacketed for heating or cooling, shell is
driven through a gear set drive with gear reducer and drive motor,
shell speed is variable via mechanical vari drive, steel support
stands are shrouded with stainless steel pharma style covers,
maximum bulk density is 50 pounds/cubic feet, intensifier bar needs
to be confirmed due to previous owner did not utilize the bar option |
|
47954- |
30 cubic
foot APV Crepaco, Cooker/Blender stainless steel jacketed, U shaped
blending tub measures 60" long x 36" wide x 36" deep, single piece
lift cover, full side & bottom jacket, rated for 95 PSI at 300º F,
scraper blade agitation with flat stainless steel mixing bars on
single shaft, 3" clamp bottom outlet, hydraulic drive, sanitary
seals |
|
35699p- |
28.8 cubic
foot Patterson Industries, stainless steel Sanitary double Ribbon
Blender, working capacity 25 cubic feet, has 24" diameter x 8' long
x 28" deep mixing chamber, 6" diameter center bottom discharge with
11" outside diameter, 8 bolt flanged connection, 41" floor
clearance, 2.5" diameter main shaft on heavy duty pillow block
bearing mounts, air purged packing gland seals, mounted on 4
stainless steel legs, former application foods. |
|
53335p- |
27 cubic
foot capacity Jacketed Ribbon Blender, approximately 24 cubic foot
working capacity, stainless steel, full hinged cover with lock down
clamps, continuous double ribbon agitator, 41" long x 31" wide x 36"
deep mixing chamber, 5 HP drive (TEFC) belt driving on shaft reducer
for final speed approximately 30 RPM, 230/460/3 phase voltage with
explosion proof controls, portable on 10" casters, 6" center bottom
discharge with manually operated butterfly valve & 24" floor
clearance, 68" total height with cover closed, 8" & 6" cover ports,
pillow block bearings & packing gland shaft seals, formerly used in
light chemical application |
|
35558p- |
20 cubic
foot Ribbon Blender, all stainless steel, mixing chamber is 66" long
x 26" wide x 28" deep, interior ribbons 1" x 1/8" x 8", outer 1-1/2"
x 3/16", 2-1/8" diameter shaft, 8" square bottom center discharge
with Teflon gate 32" from floor chain drive with gear head 1.5 HP
3/60/230/460 volt TEFC motor, 3-1/2" diameter legs, hinged cover,
overall 8' long x 30" wide x 62" high |
|
35702p- |
20 cubic
foot Posey Iron Works, carbon steel Ribbon Blender, 7.5 US 1800
220/440/3 phase dodge shaft 2/8" |
|
43571p- |
20 cubic
foot Patterson, Double Cone Blender, constructed of stainless steel,
fitted with a 6" aluminum iris valve, feed opening is 18" diameter,
blending chamber is 48" diameter x 12" straight side with 17" cones,
unit is mounted on steel channel stands & is driven by a 5 HP 460
vac 3 phase gear motor |
|
50840p- |
20 cubic
foot Patterson Kelley, V Blender, with liquids/solids bar mixer,
stainless steel shell, bar drive is 7.5 HP, main drive is 5 HP,
220/440/60/3 phase, with 65 lbs/cubic foot maximum material density,
missing the valve |
|
35569p- |
20 cubic
foot Patterson Kelley, V Blender, stainless steel, liquid solids
intensifier bar with 5 HP 3/60/20/230/460 motor, 8" discharge with
full flow valve, main drive motor is 2 HP 3/60/230/460 1750 RPM, two
18" top covers, carbon steel support frame, 8' long x 5' deep x
6-3/4' high overall |
|
46139p- |
20 cubic
foot Patterson Kelley, stainless steel Twin Shell Blender, weight
capacity rating of 65 pounds per cubic foot, stainless steel contact
surfaces with polished internal finish, direct coupled gear motor,
rotates shell at 16.5 RPM, 3 HP, 230/460/3 phase voltage, 7.4/4.2
AMP 17.5" diameter charging ports with solid removable covers, 10"
diameter discharge with manually operated butterfly valve mounted on
painted stand with extensions, externally painted shell with lifting
lugs |
|
40931p- |
20 cubic
foot capacity stainless steel Rotating V Blender, vessel legs are
32" diameter with a 6-1/2" fill port on 1 side & 6" manual butterfly
outlet valve at center bottom discharge, rotated by a double wide
chain driven by 20-25 HP gear motor, mounted on mild steel frame,
11' long x 4' wide x 6½' high with 6½' long x 4' wide x 50" high
mild steel platform, service platform overall length is 10' with 5
steps |
|
54902p- |
20 cubic
foot capacity Ribbon Blender, stainless steel, 17 cubic foot working
capacity, 24" wide x 60" long x 28" deep mixing trough, cut flight
double ribbon agitator, 7.5 HP GE drive with gear reducer chain
driving agitator 220/440/3 phase voltage, 2 piece hinged cover, 4"
center bottom discharge with manually operated swing gate, 43" floor
clearance, mounted on painted steel legs, formerly used in
pharmaceutical industry |
|
52962p- |
20 cubic
foot capacity Patterson Kelley, Twin Shell Vacuum Dryer/Blender,
stainless steel product contact parts, rated at 65 pounds per cubic
foot product density, rated for full vacuum internal, 30 PSI jacket,
liquid/solids type intensifier bar, 5 HP variable speed drive on
chamber & 5 HP fixed speed drive on intensifier bar |
|
41243p- |
18 cubic
foot capacity double ribbon Blender, 2 HP drive motor, 2' wide x 5'
long 6" diameter discharge stainless steel contact, mfg. unknown |
|
53999p- |
16 quart
Patterson Kelley, Lab Blender model LB1143, 1/4 HP single
phase/60/120V drive |
|
35568p- |
16 quart
Patterson Kelley V Blender, twin shell, 304 stainless steel, up to
125 pounds per square foot, blender chain drive 1/4 HP 1/60/110 volt
TEFC motor, intensifier bar drive 3/4 HP gear head motor 1/110 volts
V belt drive (no intensifier bar available) unit on base, could set
on table overall 28" high x 2' long x 3' wide |
|
35557p- |
16 cubic
foot Ribbon Blender, all stainless steel, mixing chamber 5' long x
2' wide x 27" deep, inner ribbons/outer ribbons are 1" x ¼", 2"
shaft, 6½" diameter bottom center discharge that tapers to a 3" tri
clamp fitting below chamber 20" from floor, chain drive 2 HP
3/60/208/230/460 TEFC gear head motor, final 45 RPM no cover, 2"
angle iron legs, 7' long x 29" wide x 57" high overall |
|
38636p- |
15 cubic
foot stainless steel dual shaft paddle Blender, 28" wide x 56" long
x 21" deep, twin shafts driven by single gear box, requires drive,
14 paddles per shaft 1.5" x 6", 7" x 4" end discharge, presently
designed for continuous mixing with removable vertical baffle 18"
deep, 21.5" from end designed to increase mixing residence time. |
|
35564p- |
15 cubic
foot Ribbon Blender, stainless steel with hopper above, 2 HP, single
ribbon 3" deep 3/8" thick, center shaft 4½" inside chamber, 3¼" at
bearings, mixer inside 5' long, 25" deep, 22" wide, 12" high hopper
above mixing chamber with hinged lid, 6" end discharge with air
gate, single chain drive with 2 HP 3/60/230/460/1750 RPM gear head
motor with 40:1 ratio, mounted on 3" x 6" carbon steel frame, 75"
long x 77" wide x 50" high overall |
|
44466p- |
15 cubic
foot Gemco, Double Cone Blender, constructed of stainless steel,
fitted with a pneumatically operated discharge valve & cylinders to
hold a 55 gallon drum in place while loading, feed opening is 16"
diameter, the blending chamber is 46" diameter x 10" straight side
with 16" cones, unit is mounted on steel channel stands & is driven
by a 3 HP 230/460 volt 3 phase gear motor |
|
52967p- |
15 cubic
foot capacity Marion, Paddle Blender model HPS2748, stainless steel,
125 PSI jacket, National Board #141, vessel rated for 30 PSI, Teflon
seals, outboard bearings, counter weighted cover with hold down
lugs, 4 curved paddles, welded construction, 6" center bottom
outlet, 5 HP drive motor |
|
42984p- |
15 cubic
foot Bepex, Double Ribbon Blender, stainless steel construction,
jacket rated 175 PSI at 750º F, National Board #198, trough measures
48" long x 28" diameter, 1" steam inlets/outlets, 8" flanged product
inlets/outlets, discharge in bottom center, 10 HP motor, 460 vac 3
phase |
|
53339p- |
14 cubic
foot capacity Double Ribbon Blender, jacketed, stainless steel, 48"
long x 24" x 31" deep mixing trough with 2 piece hinged lids opening
away from center, stainless steel sta-bolt style jacket is not rated
but will be in house tested to 25 PSI, 8" x 8" bottom end discharge
with air operated slide gate, approximately 2 HP Mitsubishi mounted
gear reduced drive with chain & sprocket ribbon drive, packing gland
shaft seals, stainless steel body with painted steel frame & legs,
used in food |
|
54903p- |
13 cubic
foot capacity Marion Mixers, Paddle Blender model S2436, sanitary
stainless steel, 10 cubic foot working capacity, 24" diameter x 36"
long mixing chamber with full hinged cover, mounted on legs,
formerly used in cosmetic industry |
|
35693p- |
12 cubic
foot Prodex Corp, stainless steel fully jacketed Double Ribbon
Blender, model 35C, features 10 cubic foot working capacity, 18"
wide x 50" long x 22" deep mixing trough, fully jacketed body with
stay bolt style jacket, packing gland shaft seals, 4" diameter
bottom end discharge with 34" floor clearance, removable ribbon, HP
drive with bolt driven on shaft gear reducer, full cover with
loading port, RPM agitator speed, painted exterior. |
|
44937p- |
11 cubic
foot capacity American Process Systems, Double Ribbon Blender, model
DRB11, 3 HP motor center discharge, 3A sanitary interior finish, one
piece hinged cover, no valve included, no control box. |
|
35556p- |
10 cubic
foot Ross, Ribbon Blender, 304 stainless steel, 3 HP drive, 4"
diameter bottom center discharge, 40" from floor, 3/16" thick,
center shaft 2.5" diameter V belt drive with dodge shaft mounted
reducer, 1/60/230 volt, 1730 RPM, 4" carbon steel legs & frame,
mixing chamber 21" wide x 4' long x 2' deep, motor starter
stop/start control, 7' long x 33" wide x 65' high overall dimension |
|
33494p- |
10 cubic
foot Ross, jacketed Ribbon Blender model 42A10RB, stainless steel,
sanitary, 21" wide x 48" long x 25" deep inner dimensions, end seals
& stuffing box, 5" center bottom outlet with flush plug valve,
eliminates dead spots in mix trough, manual crank type .5 HP
230/460/3 phase with on shaft gear reducer, 38" discharge height, 60
RPM ribbon. |
|
42987p- |
10 cubic
foot Ribbon Blender, stainless steel construction, trough measures
24" wide x 36" long x 28" deep, 1-1/4" diameter shaft, tubular
stainless frame with sanitary connections, two 1.5" bottom end
discharges with sanitary threaded connections at each bottom end,
comes equipped with 1 HP motor, 230/460 VAC, 3 phase power required,
stands on 4 legs, used for pasta & sauces |
|
52280- |
10 cubic
foot Patterson Kelley, V Blender, with liquid solids bar, maximum
density 70 lbs/cubic foot, 304 stainless steel, used for mixing
dental care products |
|
38460p- |
10 cubic
foot Patterson Kelley, V Blender, 90 pounds per cubic foot maximum
product density, disc type intensifier bar, butterfly discharge
valve, 1.5 HP shell drive 230/460 volt 3 phase, a 7.5 HP intensifier
bar drive 230/460 volt 3 phase |
|
45239p- |
10 cubic
foot Hamilton, V Blender, 316 stainless steel, unit is mounted on
stainless steel stands & base, 15" inside diameter opening, interior
is rated for 50 PSI & full vacuum at 300º F, missing lid, 2" steam
inlet & outlet with rotating couplings, National Board #5951, each
cylinder is 20" diameter & 45" long for a total capacity of 13 cubic
feet, unit is driven by a 7.5 HP motor with 40 to 1 gear reducer,
230/460 vac 3 phase power required |
|
53336p- |
10 cubic
foot capacity JH Day, Ribbon Blender model C, 80 gallon working
capacity, stainless steel, painted steel body with polished
stainless steel liner & double ribbon agitator, 21" x 48" long x 24"
deep mixing chamber, single piece cover with full dump grate, 5"
center bottom discharge with manually operated swing gate & 34"
floor clearance, APX 3 HP gear reduced drive with chain & sprocket
yielding 60 RPM agitator speed, rated for 35-45 pounds per cubic
foot product density |
|
31330p- |
10 cubic
foot capacity Grace, all stainless steel Ribbon Blender, U shaped
tub, interior tub measures 34" long x 24" wide x 29" deep, blending
blades are 3 bars 31" long x 3" wide, tube is on stainless steel
frame with end mount gear head drive, overall dimensions 6' long x
26" wide x 46" high, stainless steel cover, removable paddle
assembly, sanitary construction. |
|
49086p- |
8 quart
Patterson Kelly, V Blender |
|
52976- |
8 quart
Patterson Kelley, Twin Shell Blender, stainless steel, with pin bar,
fractional HP motors for the shell & intensifier bar, 7.5" covers,
requires 120 vac single phase electrical supply |
|
54904p- |
8 quart
Patterson Kelley, Laboratory Blender, liquid/solids, stainless
steel, all explosion proof drives, controls with non XP emergency
stop, 1/6 HP motor chain driving shell at 25 RPM, .75 HP motor belt
driving bar at 1150 RPM 115/230 single phase wired for 115 volt
service, mounted on low profile portable painted carbon steel stand,
formerly used in the food industry |
|
55001- |
6 cubic
foot capacity Day, Double Ribbon Blender, all stainless steel, 3"
center bottom discharge with slide gate, 17" wide x 38" long inside
dimensions, stainless steel covers, 1" x 5/16" outer ribbon, 1/8" x
1-1/8" inner ribbon, 3 HP 230/460 volt gear head motor |
|
51038p- |
5 cubic
foot Patterson Kelly, stainless steel Double Cone Blender, polished
stainless steel shell for food grade service, rated 200 pounds per
cubic foot product density, 30" diameter x 32" shell, 14" charging
port with removable gasketed covers, 6" discharge, pneumatically
operated butterfly valve, 16" diameter dust lid, pneumatically
operated engagement, mounted in painted factory stand, 29" high
extensions yielding 44" discharge height, GE 1.5 HP DC drive (shunt
wound) 180 volt, with gear reducer & magnetic brake chain driving
shell |
|
54336- |
5 cubic
foot Patterson Kelley, V Blender, stainless steel |
|
48302p- |
5 cubic
foot Patterson Kelley, V Blender with a maximum material density of
95 pounds per cubic foot, stainless steel product contact with mild
steel frame, 6" discharge with solids flow butterfly valve, 3/4 HP
230/460 volt brake motor, liquid addition capability |
|
48648p- |
5 cubic
foot Patterson Kelley, V Blender stainless steel product contact,
mild steel frame 6" butterfly discharge valve, 3 HP gear head motor
480 volt 3 phase, 25 final RPM, 65 pounds per cubic foot maximum
product density |
|
55279p- |
4 quart
Lab Blender model LB11155, V design with liquid/solids intensifier
bar, stainless steel, rated for 150 pounds/cubic foot, 110 volt
power required |
|
43651p- |
3 cubic
foot Patterson Kelley, V Tumble Blender, model 3, 304 stainless
steel contact with bar drive, rated 60 pound/cubic foot, butterfly
gate discharge, stainless steel locking covers, 3/60/230v power
required |
|
53888- |
3 cubic
foot Patterson Kelley stainless steel V Blender with high speed
intensifier bar, maximum density 85 pounds per cubic foot,
208-230/460/60/3 phase electrical, with control panel, covers and
valve |
|
53887p- |
2 cubic
foot, Patterson Kelley V Blender with intensifier bar, 60 pounds
cubic foot maximum density. |
|
53338p- |
2 cubic
foot Patterson Kelley, Twin Shell Blender, all stainless steel
contacts with intensifier bar & 85 pound per cubic foot maximum
material density weight rating 1/3 HP explosion proof dust tight
shell drive by Master Electric final speed of 25 RPM, motor UL rated
for class I/group D class II/groups F & G, intensifier bar is belt
driven via 1.5 HP drive by Baldor belt driving bar at approximately
1100 RPM, mounted in painted mild steel frame, manual, swing plate
discharge |
|
55115- |
1 cubic
foot V Blender, stainless steel liquid add bar, protective cage
around blender, complete with drive |
|
53998p- |
1 cubic
foot V Blender with stainless contact parts, rated at 400
pound/cubic foot, 8" covers with 4" manual butterfly discharge,
mounted on steel base with casters, 1/3 HP 60/220-440V drive |
|
44013p- |
1 cubic
foot Patterson Kelley, V Blender model 1, processor with liquid
solids bar, polished stainless steel internal, carbon steel jacketed
with internal vacuum rating, 11 x 18" shells, solids intensifier bar
included, 6" butterfly discharge 3/4 HP main & 1 HP bar drive,
3/60/230-460 volt power required National Board #66994, shell rated
full vacuum at 250º F, jacket rated 30 PSI at 250º F, includes
process skid with immersion heater Watlow, pump & heat exchanger &
tank |
|
53889p- |
1 cubic
foot Patterson Kelley stainless steel V Blender with high speed
intensifier bar, maximum density 80 pounds per cubic foot,
208-230/460/60/3 phase electrical, with guard, covers and valve. |
|
55281- |
1 cubic
foot Marion, Paddle Blender model 1002, lab size, stainless steel,
jacketed trough, butterfly discharge, stainless cover, pipe leg
extensions on casters, 1.5 HP 220 volt GH drive |
|
52281p- |
.5 liter
(.017 cubic foot) Gemco, Blender model GLB, slant cone, stainless
steel construction, bench top cantilevered design, rated 65 lb/cubic
foot maximum material density, 1/2 HP 115 volt motor with AC
inverter, 38-72 RPM |
|
|
