Storage Tanks
New Arrivals
Inventory
Agitator Types
Home Page
Refrigerated Horizontal
Refrigerated Vertical
Refrigerated Rectangular
Insulated Horizontal
Insulated Vertical
Insulated Rectangular
Single Shell Horizontal
Single Shell Rectangular
Silo
Cone Bottom
Farm Tank
Multicompartment
Sugar
Truck Tank
Other Than Dairy
Vacuum Tank
|
|
Item # |
DESCRIPTION |
|
58545p- |
7,950
gallon Mueller, Wine Fermentation Tank, 30,000 liter, all stainless
steel construction, 11' diameter x 16.5' high, jacketed |
|
55633p- |
7,500
gallon Damrow, Insulated Tank, stainless steel, vertical, 8' 6"
diameter x 21' 6" high, 2-1/2" clamp outlet, 2" clamp inlet, shell
for level sensor, 50" wide x 60" high alcove |
|
52385p- |
5,500
liter Mueller, Jacketed Tank, "Ultra Filtration Skid Tank One" tank,
stainless steel, dome top & bottom, 18" manhole, (2) 6" (2) 1.5" (2)
4" inlets, 1.5 HP top mounted agitator with dual 3 blade impeller,
vessel info design temperature 200º F |
|
53808p- |
5,000
gallon Dairy Craft, Dairy Tank model 76J, 1/3 jacket bottom up,
2-1/2" insulation, holding milk at 37º F, 17' 8" x 9' 6", stainless
steel inside, painted outside |
|
46638- |
3,500
gallon Walker, Insulated Mix & Blend Tank model VHT4498, dome top
dished bottom, stainless steel, type 316L 2B product contact
surface, Lightnin off center mounted 5 HP 56 RPM propeller agitation
with bolt on blades, CIP devices, stainless steel side mounting tabs
less leg assembly, with Sparger ring, Approximate dimensions are
133" x 133" (including angles for legs which are not included) x
145" overall height including gear head. |
|
42892p- |
2,500
gallon Cherry Burrell, insulated mix and blend tank, dome top flat
bottom, 316 SS, #4 finish inside,100 square foot channel wall
surface on sidewall, 4 zones 35 square foot channel wall surface on
bottom head, 1 zone basic header design, 1¼" NPT male connections
for water, 2½" bevel seat outlet, sprayball, vertical off center
mounted with dual 20" diameter 4 bladed axial flow turbines 3 HP
single speed motor, 97 RPM 230-460/3/60, less baffle, 84" D x 115"
straight side x 160" OH, (3) 2" inlets |
|
50932p- |
2,100
gallon Walker, Jacketed Holding Tank, model SP, dome top with hinged
manway, dish bottom, (2) 6" & (1) 4" flange top ports, 2" center
bottom outlet, approximate 28" outlet height, Rosemount level sensor
fitting only, 1 side & 1 bottom heat exchange zone, 98" diameter x
134" high, mild steel legs with pad feet |
|
1568p- |
2,000
gallon Heil, Vertical Design Insulated Tank, stainless steel,
vertical agitation, 3" center bottom outlet, side entering manway,
7' 8" diameter x 8' 6" high. |
|
44275- |
2,000
gallon capacity APV Crepaco, Tank stainless steel construction 18"
manhole missing cover, heavy duty sweep agitator blade, 7' deep on
straight side & slight cone to center discharge, 4" tri clamp
outlet, 50 PSI jacket, tank is pitted on the inside & leaks into the
jacket it is stressed & cannot be welded, good for a holding tank |
|
56592p- |
13,000
gallon capacity Ellet, Jacketed Tank, sanitary 304 stainless steel
construction, 14' 6" diameter x 10' 8" straight side, flat top &
sloped bottom, 3 water jacketed rings near top of tank, (1) 6" & (1)
12" x 14" center top openings, side openings include (1) 2"
threaded, (1) 1" for temperature gauge, (1) 1/2" sample valve & (1)
13 x 18" manway with cover, bottom includes 10" sump type outlet,
tapered to 3" threaded tangential outlet, last used for storing wine |
|
58870p- |
1,250
gallon Walker, Jacketed Tank, 316 stainless steel, vertical, jacket
rated 100 PSI at 300º F, ASME #465, 30 HP 1765 RPM motor that
reduces to 130 RPM, (2) 36" diameter 3 blade agitator, 10" dome top,
12" dish bottom, 72" interior diameter x 72" straight side height,
overall dimensions with agitator & legs 84" diameter x 190" tall,
top has 18" manway, 4" sanitary tri clamp inlet, (3) 3" sanitary tri
clamp inlets, (2) 1.5" sanitary tri clamp inlets, CIP ball, bottom
has 4" sanitary tri clamp center discharge 48" from the ground, 4"
outlet, requires 230/460 vac 3 phase electrical supply |
|
58869p- |
1,250
gallon Walker, Jacketed Tank, 316 stainless steel, vertical, jacket
rated 100 PSI at 300º F, ASME #464, 30 HP 1765 RPM motor that
appears to reduce to 130 RPM (reducer tag missing), (2) 36" diameter
3 blade agitator, 10" dome top, 12" dish bottom, interior diameter
72" x 72" straight side height, overall dimensions with agitator &
legs 84" diameter x 190" tall, top has 18" manway, 4" sanitary tri
clamp inlet, (3) 3" sanitary tri clamp inlets, (2) 1.5" sanitary tri
clamp inlets, 1" sanitary tri clamp inlet, CIP ball, bottom has 4"
sanitary tri clamp center discharge 48" from ground, 4" outlet,
requires 230/460 vac 3 phase electrical supply |
|
11269- |
1,200
gallon Storage Tank, vertical, open top with a 3" center bottom
discharge slightly dished, inside measurements 71" on the straight
side x 71" diameter, unit is constructed of stainless steel food
grade & has a stainless steel coil located in the bottom, the coils
are set so that they are 1-3/4" apart & the inlet for the material,
4 carbon steel supports on the side that is 4" wide & has legs, has
4" stainless steel rings on bottom for support |
|
25524p- |
1,000
gallon Tank, vertical, stainless steel, 92" overall height, on angle
legs, 2 sets of steam coils in bottom, sight gauge to measure
volume, two 1.25" inlets in top, 4" agitator opening in top, channel
to mount agitator on top, two 1" inlets in top, 1.25" bottom outlet,
2" bottom side outlet, three 1.5" side inlets |
|
11265- |
1,000
gallon Storage Tank, stainless steel, vertical, dual coil, 6'
straight side. |
|
21562p- |
1,000
gallon PermaSan, Sanitary Tank, stainless steel open top, 66"
diameter x 72" straight side, slight dish bottom, has loose fitting
cover, fully shrouded & insulated, 2" center bottom discharge with
ball valve, 4 bolt flanged connection, features heavy duty bridge
for mixer mounting set slightly offset of center, mounted on 5 hip
socket legs, small internal patches, repairs are sanitary grade. |
|
55201p- |
1,000
gallon Mixing Tank, stainless steel, 5 HP twin prop agitator that
turns at 58 RPM, has low pressure carbon steel jacket, 60" diameter
x 76" straight height x 10" dish bottom & top, top has (2) 18"
manway with (3) 3", (2) 4" & (1) 6" flanged fittings, bottom has 2"
flanged discharge & (2) 4" flanged fittings for jacket, overall
dimensions are 64" diameter x 164" tall, sets on 4 carbon steel
legs, requires 230/460 vac 3 phase electrical supply |
|
58256p- |
1,000
gallon Feldmeier, Insulated Tank, vertical, 316L stainless steel,
dished top & conical bottom, 72" diameter x 132" overall height, 60"
straight side height x 8" dish x 20" cone, top has 18" manway, (3)
2" sanitary tri clamp inlet, 1" sanitary tri clamp inlet, lift lugs,
2 HP gear reduced to 98 RPM (2) 3 blade axial flow turbine agitator,
side has liquid level gauge setup but no glass tube, bottom has 3"
sanitary tri clamp center discharge, 3" sanitary tri clamp, requires
440 vac 3 phase electrical |
|
25556p- |
1,000
gallon Crepaco, Single Shell Mix & Blend Tank, dome top dished
bottom, squirrel cage agitation, sprayball, bottom head jacketed &
insulated, 2" clamp outlet. |
|
5902p- |
1,000
gallon Cherry Burrell, Vertical Design Insulated Tank model D, no
agitation, 2" clamp outlet, lower manhole, top fill & sight glass,
6' diameter x 7' 6" high. |
|
58059p- |
1,000
gallon Cherry Burrell, Storage Tank, jacketed, vertical, sanitary,
approximately 66" ID x 68" on straight side with dished & welded
heads, mounted on 4 pipe legs putting the center bottom outlet
approximately 10" off the floor, top manway with hinged cover,
jacket extends up entire side, 3 HP side entering agitator
(3/60/230-460V), last used in pharmaceutical service |
|
57395p- |
1,000
gallon Cherry Burrell Insulated Mix Tank, model WPT, bridge and
cover top, wide bottom sweep agitator with adjustable baffle, flat
sloped bottom, double spray ball assembly, 2" outlet, 78" diameter x
96" overall height |
|
58580p- |
900 gallon
Storage Tank, stainless steel, 48" diameter x 9' 6" high on straight
side, lug mounted, cone top & bottom, 4" diameter flanged bottom
outlet, carbon steel jacket but has several holes in it |
|
57549p- |
750 gallon
Insulated Tank, stainless steel construction, 5' diameter x 5'
straight side, open top, slight cone bottom, leading to
approximately 2" center bottom discharge, skirt mounted |
|
44416p- |
735 gallon
Hot Oil Low Pressure Jacket Tank, 20 HP agitator in top (no motor),
flat top, dish bottom, 52" diameter x 80" high, 3" ball valve in
bottom, 2" bottom outlet, four 3.5" pipe legs, 7" wide x 12" long
manway in top, 3" flanged inlet in top, 6" inlet in top, five 2"
side openings, 3.75" shaft, stainless steel |
|
55200p- |
700 gallon
Perma San, Jacketed Tank, stainless steel, clamp on agitator,
National Board #4611, interior dimensions of 60" diameter x 54"
straight side height x 6" dished bottom, overall exterior dimensions
with legs are 63" diameter x 83" high, dimpled jacket rated for 55
PSI at 300º F & covers bottom & lower 36" of sidewall, jacket has
1.5" threaded connections, tank has 2" threaded center discharge,
sits on 4 stainless steel legs, equipped with thermowell, 1/4 HP
clamp on agitator which has 48" long x 3/4" diameter shaft 3 blade
10" prop, requires 230/460 vac 3 phase electrical supply |
|
54548p- |
700 gallon
Open Top Tank, sanitary stainless steel, dual jacket (sidewall
jacket leaks-not repairable, bottom jacket okay), 53" diameter x 74"
straight side, dish bottom 6" deep, 4 internal baffles, 37" high x
5" wide, top stainless steel bridge mixer mount, 3" center bottom
outlet, 2 temperature probes, dimple style jacket, 24" discharge
height, mounted on 4 painted carbon steel 3" pipe legs with gussets,
1.5 HP centrifugal pump piped to discharge & mounted under vessel |
|
46370p- |
650 gallon
Kennedy, Insulated Tank, stainless steel, 4-1/2' diameter x 5-1/2'
high, top mounted Chemineer 1/2 HP agitator with 1725 RPM & gear
reducer for a final RPM of 430, flat top & cone bottom with 1.5"
center bottom outlet |
|
45256p- |
600 gallon
Sani-Tank, Insulated Mix & Blend Tank with center bridge lift top
covers, super mixer agitation, 2.5" clamp outlet, flat bottom |
|
54759p- |
600 gallon
Cherry Burrell, Insulated Tank model WPT, stainless steel, 64"
diameter x 46" straight side with open top & flat bottom, agitation
with top entering bridge mounted 5 HP 230/460 volt 1725 RPM drive,
2" side bottom discharge, sweep type agitation |
|
7789p- |
600 gallon
Cherry Burrell, Insulated Mix & Blend Tank, dome top, vertical high
shear agitation, sprayball, 2.5" clamp outlet. |
|
54760- |
600 gallon
capacity Tank, stainless steel construction, 4' diameter x 6' deep,
flat top, dished bottom with center bottom outlet, jacket with
stainless steel shroud, complete with sweep/scraper agitation,
driven by 3 HP motor |
|
58556- |
550 gallon
Overly Inc., Storage Tank, 316 stainless steel, jacketed for 25 PSI
at 160º F, flat top, dished bottom, hinged lid on top 2/3 of tank,
on stainless steel legs, National Board #80575 |
|
30788p- |
500 gallon
Storage Tank, stainless steel, 42" diameter x 6' tall, open top,
flat bottom, mounted on 4 pipe legs, 2" side bottom discharge, unit
includes a top side entering agitator, 1/2 water jacket on bottom |
|
7815p- |
500 gallon
SFI, Insulated Mix & Blend Tank, dome top, dish bottom, .87 HP
Lightnin mixer agitation, sprayball, 2.5" outlet pod only. |
|
51014- |
500 gallon
Precision Stainless, Mix Tank model 83483, process with 5 HP GH
agitation, 316 stainless steel, rated 100 PSI, -25º to 250º, 48"
diameter, 304 stainless steel jacket |
|
58555p- |
500 gallon
Pan Handle, Storage Tank, stainless steel, 48" diameter x 66"
straight side, dished bottom, atmospherical internal at 400º F, 14
PSI at 400º F on the stainless steel dimple jacket, flat bolt on top
with 2" diameter pipe fittings, 4" diameter center bottom outlet,
flanged, mounted on skid & 4 angle iron legs, National Board #1171 |
|
47474p- |
500 gallon
capacity Tank, all stainless steel, includes jacket & appears to be
insulated, 48" diameter x 64" straight side, dished top with 18"
manway & cover, 2.5" center top opening, 2-3/4" vent & 4 other top
inlets, slight sloped bottom leading to 1-3/4" side bottom outlet,
mounted on stainless steel pipe legs & has side attached ladder |
|
33142p- |
475 gallon
Tank, stainless steel 4' diameter x 5' straight side height with
dished bottom & flat top, lug mounted, has 4' straight height,
carbon steel jacket. |
|
35854p- |
475 gallon
Jacketed Tank, stainless steel sanitary, closed top, insulated body,
full non rated jacket, concave bottom to 1.5 discharge with 2 way
plug valve, carbon steel legs, jacket is unusable, leaking into
internal shroud, 54" x 80" high, 20" discharge height, side bottom
outlet 2" reduced to 1" internal dimensions 48" diameter x 48" deep,
slope bottom, 43" approximate on side to 48" raised dairy tank for
possible mixer mount in center bottom. |
|
39385- |
450 gallon
Jacketed Tank, stainless steel, 4' 4" x 4' 4", dished top/bottom,
jacketed for water, 16" manway top, side mounted agitator, less
drive |
|
47832p- |
450 gallon
Jacketed Tank, 316 stainless steel on legs, 48" sidewall, 54"
diameter, 6' cone bottom |
|
11244p- |
400 gallon
Storage Tank, 304 stainless steel, open top, flat bottom drain,
insulated, side agitator, no drive included, 52" inner diameter x
58" deep, 2 drains, 4" & 2" at each side of the bottom, temperature
probe 4 carbon steel legs, raise bottom 18' off floor, tank is 78"
high overall |
|
37447p- |
400 gallon
Crepaco, Tank, stainless steel in/out with insulation, 2" side
bottom outlet, covers, mild steel legs, some minor pitting in the
lower 12" of the tank, 50" diameter x 50" deep, bottom has slight
slope to the outlet |
|
58423- |
400 gallon
Chester Jensen, Mix & Blend Tank, insulated, stainless steel, bridge
& cover top, cone bottom, 316L product contact surface, wide bottom
sweep agitator, baffle, 3" clamp outlet, 20" outlet height,
insulated sides & bottom, 86" diameter x 93-11/16" OAHT, stainless
steel legs with adjustable pad feet |
|
56369- |
400 gallon
Chester Jensen, Insulated Mix & Blend Tank, center bridge with lift
top covers, wide sweep agitator with baffle, 2" clamp outlet, minor
interior distortion |
|
55199p- |
392 gallon
Tank, 316 stainless steel, vertical, 54" diameter x 46" straight
side height, overall height excluding scale of 88", slope bottom,
flat top, low pressure jacket with insulation, 4" bottom flanged
discharge, 2" top flanged fitting, 1/3 HP Lightnin agitator, mounted
on 5,000 pound mechanical scale system, side constructed of 3/16"
316 stainless steel, bottom & top is 10 gauge 316 stainless steel |
|
51357p- |
375 gallon
Tank, stainless steel, 4' diameter x 4' straight side, unit features
open top with dish bottom to 3" diameter center bottom discharge,
mounted on carbon steel frame for forklift access |
|
58254p- |
375 gallon
Coastal Technologies, Jacketed Tank, vertical, dimple jacket,
stainless steel, clamp on jacket rated for 150 PSI at 400º F,
National Board #29908, dome top, dish bottom, 36" diameter x 120"
overall height x 72" straight side height, dish & dome are 10", top
has (2) 4" flanges, (2) 1" NPT, 2" sanitary tri clamp & 1.5"
sanitary tri clamp, side has 18" manway, 3" sanitary tri clamp, 1"
sanitary tri clamp & clamp on jacket, bottom has 2.5" sanitary tri
clamp center discharge, .75" NPT, (2) 2.5" sanitary tri clamp, & 2"
sanitary tri clamp |
|
54752p- |
375 gallon
capacity Tank, stainless steel contacts, 48" diameter x 48" straight
side, dished top with convex type bottom, leads to 2" side bottom
outlet, includes carbon steel jacket, complete with sweep type
agitation with scrape blade connections for sidewalls, agitator
driven by 5 HP 208-230/460 volt 1735 RPM motor thru gearbox |
|
37894p- |
345 gallon
Clauson, Tank, 50" diameter x 40" high, stainless steel, 1 HP 3
blade agitator with 1725 RPM flat top with 20" square manway, flat
bottom, inlet is 1/2" on side, 1.5" side bottom outlet, top half is
insulated, no legs |
|
56650- |
300 gallon
Insulated Tank, stainless steel, open top vertical, 49" diameter x
43" deep x 53" high, 2" clamp outlet, former Sterline processor |
|
7842- |
300 gallon
Crepaco, Insulated Mix & Blend Tank, center bridge with lift top
covers, standard agitation, 2" clamp outlet. |
|
38711p- |
284 gallon
DCI, Deareator Tank, vertical cylindrical, single shell, dome top,
18" side pressure manway, sight glass, dish bottom, 1 each 2" clamp
top inlet & two 4" clamp top ports, one 4" flange top port, 4" clamp
outlet, approximately 14" outlet height, vessel MAWP 0/-15 PSI at
350º F, minimum, design metal temperature -20º F at 0 PSI, 36"
diameter x 142" overall height, stainless steel legs with adjustable
pad feet |
|
57775p- |
280 gallon
Mixing Tank, open top, flow thru jacketed, 47" diameter x 38"
straight side with dish bottom, 1.5" center bottom outlet piped to
perimeter of tank with 5" OD 4 bolt flanged connection 12" from
floor, full dome top cover with hydraulic assist, angular entry
agitator, 220 volt single phase, jacketed body is designed for
continuous flow thru heating or cooling media, formerly blending
olive oil |
|
18376- |
200 gallon
Crepaco, Batch Weigh System, single weigh tank, single electronic
tension type load cell & mild steel support structure, sprayball,
less control package |
|
26899p- |
200 gallon
Creamery Package, Mix Tank, vertical cylindrical, stainless steel
exterior, dome top, sloped bottom, 1.5" tri clamp outlet, 36" high x
44" diameter tank dimensions, 93" high x 52" diameter overall
dimensions, center type agitation, sprayball, manhole, 3/4 HP, 33/64
RPM, 230/440 voltage, 3 phase. |
|
47622- |
200 gallon
Chester Jensen, Insulated Mix & Blend Tank, model 70N20, stainless
steel cooker/cooler, center bridge with lift top covers, double
motion wide sweep agitation with scraper blades & baffle, 3" clamp
outlet, the jacket is not repairable |
|
47325p- |
185 gallon
St. Regis, Vertical Tank, stainless steel, 40" diameter x 34"
straight side height, dome top has 18" manway (cover missing), four
2" sanitary & 1" sanitary fittings, concave bottom for positive flow
to 2" bottom outlet, side thermowell, 2" sanitary, 3" sanitary & 1"
sanitary fittings, supported by 3 adjustable legs, 62" overall
height. Prior use is unknown. |
|
43070p- |
150 gallon
Jacketed Tank, stainless steel closed top, with manway, very heavy
duty steel, never used |
|
57784p- |
125 gallon
Jacketed Tank, stainless steel, closed top, 32" diameter x 36"
straight side x 6" dished heads, full jacket, 3 steel legs, no
jacket rating, top opening accepting 7" diameter 6 bolt flange
connection, (2) 1" center bottom discharge, formerly used in food
starch manufacturing |
|
30677- |
100 gallon
Mueller, Jacketed Tank, single shell, open top, dish bottom with 1"
MNPT outlet, un-insulated side pressure wall surface. |
|
48331- |
100 gallon
Insulated Mix Tank, 2 piece hinged cover, reverse dish bottom,
vertical agitator, sprayball, 37" diameter x 72" overall height,
stainless steel legs with adjustable ball feet |
|
51346p- |
88 gallon
Vertical Tank, open top, cone bottom, measures 34" diameter x 24"
straight side, has 1.5" center bottom outlet, insulated, jacketed,
mounted on 4 stainless steel pipe legs with casters, previously
stored deionized water |
|
7596p- |
75 gallon
Damrow, Insulated Mix Tank, stainless steel exterior & bottom, 2
piece removable hinged cover, reverse dish bottom, 1.5 top inlet, 2"
side bottom outlet, mounted on 12" mild steel legs, 37½" diameter x
36" high. |
|
48210p- |
75 gallon
capacity Mix Tank, 24" diameter x 36" straight side x 6" dish open
top stainless steel, 1" center bottom outlet tangential vessel is
fully jacketed & equipped with 1/4 HP DC drive with 2 paddles full
sweep no scrape |
|
54539p- |
60 gallon
Tri Canada, Open Top Tank, sanitary stainless steel, 26" diameter x
30" straight side, slight dish bottom outlet with tri clamp
connection & 12" floor clearance mounted on casters with 4
interconnected legs, portable mix mounting station, loose fitting 2
piece hinged cover with mixer entry slot, vessel has stainless steel
dimple jacket which is welded closed, formerly used in food industry |
|
56811p- |
60 gallon
Open Top Sanitary jacketed Mixing Tank, 24" x 36" deep with dish
bottom, 1.5" center bottom discharge, mounted in stainless steel
frame with casters |
|
54937p- |
60 gallon
Jacketed Tank, open top, jacket is non rated, equipped with 2.5" NPT
fitting for electric Bayne theater in base of jacket, 3 lifting
lugs, full loose fitting cover, casters, 10" EZ roll mounted wheels,
25" diameter x 32" deep internal dimensions |
|
57773p- |
50 gallon
Pfaudler, Percolation Tank, open top, jacketed, vertical, 316
stainless steel vessel with carbon steel jacket, National Board
rated (#37879 V&W stamp 1977) for 90 PSI at 350º F, shell is rated
for full vacuum at 60 PSI at 350º F (75 PSI without vacuum), 24"
diameter x 25" straight side with 3" dish bottom 2" center bottom
discharge with Pfaudler flush seating valve & 25" floor clearance,
mounted on 3 interconnected legs with casters, stainless screen is
mounted 20" from brim with 1/2" diameter holes & welded to rolled
angle iron support frame on wall, formerly used in food ingredients |
|
1829p- |
50 gallon
Insulated Tank, stainless steel vertical, open top, 24" diameter x
48" high x 30" deep, 2 piece cover, 1.5" outlet (former Cherry
Burrell atmospheric jacket processor) |
|
57094p- |
40 gallon
Four Corp, Jacketed Tank, 316L stainless steel, sanitary, fully
jacketed, shrouded & insulated body National Board rated (#237) for
75 PSI at 320º F & internal pressure rating of 65 PSI at FV at 320º
F, dish top & bottom with removable cover & 6 swing bolt closures, 8
top inlets with tri clamp connections (2-3", 2-2.5", 1-2", 1-1.5",
2-.75") & (1) 6" 8-bolt flanged inlet with mixer mating flange, 3
bottom side inlets, mounted on 4 interconnected stainless steel legs
with casters & 1.5" center bottom discharge with tri clamp
connection & 14" floor clearance, 18" diameter x 36" straight side |
|
50714p- |
30 gallon
United Utensils, Jacketed Tank, vertical, stainless steel, 150 PSI
jacket 20" wide, 1.5" center bottom outlet NPT, mild steel legs with
casters, 17-3/4" inside diameter x 30-1/2" deep, 48" overall height |
|
48628p- |
30 gallon
Jacketed Melting Tank, stainless steel, 18" diameter x 28" deep,
open top with half bolt on cover, liquid fill & heat from electric
source, formerly heated with Bayonet heater mounted at base of
jacket with separate drain & fill ports, flat sloped bottom with 1"
discharge with manual valve for slow hot pour fillings of molds or
containers, mounted on 3 stainless steel legs with 8" clearance
under vessel |
|
53316p- |
30 gallon
Jacketed Melting Tank, stainless steel, 18" diameter x 28" deep,
open top with 1/2 bolt on cover, slow speed paddle agitator with
Baldor 1/4 HP DC variable speed drive 90 volt single phase 104 RPM,
liquid fill & heat from electric source, formerly heated with
Bayonet heater mounted at base of jacket with separate drain & fill
ports, flat sloped bottom to 1" discharge with manual valve for slow
hot pour filling of molds or containers, mounted on 3 stainless
steel legs with 8" clearance |
|
46305p- |
25 gallon
Open Top Tank, stainless steel, jacketed body with full insulation,
aluminum & sheathing, 18" diameter x 24" deep, 30 degree cone bottom
with 3/4" center bottom outlet, NPT connection & 24" floor
clearance, carbon steel mounting for portable clamp mount mixer,
bolt on cover & mounted on 3 carbon steel legs |
|
54703p- |
25 gallon
Jacketed Tank, stainless steel, 18" diameter x 24" tall, open top,
flat bottom, 1" side discharge, jacketed with Chromalox heater, will
heat up to 250º F, has site glass, 120 volt heater |
|
55978p- |
20 gallon
Holding Tank, jacketed, 316L product contact surface, dome top with
16" hinged cover, shallow cone bottom, removable sprayball, 2-1/2"
clamp center bottom outlet, thermowell, steam jacket, 21" diameter x
35" OAHT |
|
58539p- |
15 gallon
Receiver Tank, stainless steel, 12" diameter x 31" straight side
with (2) 4" flange on side, 2" threaded inlet, unit is jacketed
rated for 150 PSI at 200º F |
|
57152p- |
15 gallon
Asada, Jacketed Tank, 15-3/4" ID x 19-3/4" deep, stainless steel
tank on casters, low pressure jacket 15" wide, 1" center bottom
outlet NPT |
|
58573p- |
12 gallon
Jacketed Tank, stainless steel construction, 12" diameter x 28"
high, polished internals, agitated with (2) 4 blade paddles mounted
on common shaft, 7 sample ports at bottom, 1" diameter with 2 ports
including Intrac 797 sterilizable retractable housings, top head
includes numerous openings ranging from 1/2" to 1-1/2", 10" long
sight glass near top of vessel |
|
57158p- |
8 gallon
capacity Tank, stainless steel, 15-3/4" ID x 12-1/2" deep, 1" center
bottom outlet NPT, low pressure jacket |
|
58542p- |
2 gallon
Alloy Products, Jacketed Tank, 316L stainless steel, measures 8"
diameter x 10" straight side with open top & dish bottom, jacket
rated for 50 PSI at 100º F, 1/2" center bottom outlet, skirt mounted
with 2 access ports |
|
58541p- |
2 gallon
Alloy Products, Jacketed Tank, 304L stainless steel, measures 8"
diameter x 10" straight side with open top & dish bottom, cover,
jacket rated for 50 PSI at 100º F, 1/2" center bottom outlet, skirt
mounted with 2 access ports |
|
|
