     
New Arrivals
Inventory |
|
Item # |
DESCRIPTION |
|
32529p- |
Alfa
Laval, Contherm Scraped Surface Heat Exchanger 6" diameter x 42"
long tube, designed for vertical mounting, with belt drive motor,
usable for steam or water heating. does not have belts) |
|
41264p- |
Alfa
Laval, Contherm Scraped Surface Heat Exchanger model 6x9 control
panel stainless steel product contact 10 HP motors mounted on a
common frame |
|
38478- |
Alfa
Laval, Scraped Surface Heat Exchanger 6"x36" tubes 3 tubes total two
tubes are jacketed & one is single wall for conditioning all
hydraulic driven with power pack & stainless steel product contacts |
|
38479p- |
Alfa
Laval, Scraped Surface Heat Exchanger model 6x9, 450 PSI working
pressure |
|
42822p- |
Alfa
Laval, Scraped Surface Heat Exchanger model 6x9, hydraulically
driven, 2" inlet and outlet, 2" diameter stator, 6" x 72" tube |
|
27997- |
APV
Crepaco, Scraped Surface Heat Exchanger model 07713, 6"x72" long, 3"
tri clamp ports, overall dimensions 8'6" long x 3' wide x 4' high,
designed for Freon cooling, mutator is powered by a 20 HP Euro-drive
motor, with gear reducer to 242 RPM, less compressor. |
|
41289p- |
APV
Crepaco, Triple Scraped Surface Package mounted heat exchanger model
HD 620 unit features 3-6" diameter x 20" scraped surface heat
exchangers mounted horizontally 6 square feet each driven by
3-sterling 3 HP drives 230/460 volt triple phase 74 to 689 RPM built
1981 heat exchangers rated for 150 PSI at 375º F sanitary design
rated for maximum viscosity of 100,000 CPS heavy duty construction
may be used for heating or cooling has stainless steel shrouding and
control panel |
|
38480- |
APV,
Scraped Surface Heat Exchanger model 6x72, 3 tube never used 2
bottom tubes were manufactured to run Freon top tube is for heating
or chilled water 15HP SEW euro drive motor 293 TPM on top tube & 20
HP SEW euro drive motors with 302 final RPM on the bottom barrels,
150 PSI NB# 9131 |
|
36396p- |
APV,
Scraped Surface Heat Exchanger model HD672, 6"x72" chrome plated
nickel barrel rated at 400 PSI, 2½" product connections, direct
drive, mounted on stainless steel frame, national board #8016, steam
jacket rated for 150 PSI at400ºF, frame dimensions 148" long x
34"wide x 38"high, stainless steel scrapes, was never used, was set
up for meat |
|
40415- |
Armstrong,
Votator 12"x13", single, stainless steel, steam, 1.5 HP, 12"x13',
300 PSI tube, 150 PSI on jacket, chain drive with starter switch &
is horizontal design. |
|
41369p- |
Chemetron
Process Equipment, Votator Scraped Surface Heat Exchanger, top
cylinder is 6" diameter x 10' long, the bottom cylinder is 13" x 72"
long, model L-SAN-L00 |
|
651- |
Chemetron
Process Equipment, Votator, 7½ HP, 10"x20' long. |
|
40418p- |
Chemetron,
single Votator 4"x48" model M41F. |
|
42552- |
Chemetron,
Votator 10"x20' long 7.5HP |
|
40424- |
Chemetron,
Votator 6"x48" model FV183A, triple, stainless steel, ammonia, 25
HP, chrome plated barrels, V-belt motor drive 250 PSI internal
jacketed for 150 PSI last running pineapple juice concentrate, set
up with Ammonia expansion. |
|
40369p- |
Chemetron,
Votator 6"x72", stainless steel, single, jacket, 400 PSI internal at
375ºF., jacket rated for 150 PSI internal at 375ºF., stainless steel
feed & discharge, unitized on skid with 30 HP 1750 RPM, 230/460 volt
main drive motor, V-belt to gearbox, National Board # 2101
|
|
40758- |
Chemetron,
Votator model 1C624L, 6"x24" stainless steel, driven by 5HP US vari
drive, 220/440 volt with speed range of 97 RPM minimum to 867 RPM
maximum, unitized on frame, complete with some controls, rated at
250 PSI at 375ºF. mounted on stand, last run at tomato processing
plant as a steam heated cooker |
|
27994p- |
Chemetron,
Votator Scraped Surface Heat Exchanger, 12"x72" long, rated for 250
PSI internal at 375°F., 150 PSI at 375°F. jacket rating, 10 HP
drive, designed for product heating. |
|
38481- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 324 thermutator 3"
diameter x 24" long 5 HP variable motor |
|
32528- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 6"x48" SWB, 6"
diameter x 56" long barrel designed for heating or cooling with
liquid media or steam, measures 8' long x 6' wide x 75" high. |
|
27999p- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 6"x72" S, 6" diameter
x 72" tube designed for heating or cooling with liquid media or
steam, measures 11' long x 6' wide x 3' high, 9 square foot of heat
transfer surface, single tube unit. 1-1/2" connections |
|
32527p- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 6"x72" SWB, 6"
diameter x 90" long barrel, designed for heating or cooling with
liquid media or steam, measures 11' long x 40" wide x 52"
high.1-1/2" connections needs repairs to tubes, not presently ready
for service |
|
37526- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 624DE, direct
expansion ammonia, 6" inside diameter x 24" long tube, with
accumulator, 10 HP Reeves vari drive motor, chrome barrel with
stainless steel scraper blades |
|
38483- |
Cherry
Burrell, Scraped Surface Heat Exchanger model 672 DE twin tube unit
direct expansion with accumulators hydraulic drives chrome barrel |
|
38482- |
Cherry
Burrell, Scraped Surface Heat Exchanger model DE 624 6"x24 " stator
is 5-1/4" in diameter 5 HP variable speed |
|
45007p- |
Cherry
Burrell, Scraped Surface Heat Exchanger model DE 624 6"x24" stator
is 5.25" diameter stainless steel product contact 5 HP variable
speed drive motor |
|
36348- |
Cherry
Burrell, Scraped Surface Heat Exchanger thermutator, model 6489 |
|
17258p- |
Cherry
Burrell, Thermutator model 6"x48" x 3, (3) barrel. |
|
33973- |
Cherry
Burrell, Thermutator model 6"x72", 3 tubes, all stainless steel, 9
square foot heat transfer surface per tube. Sweep surface Heat
Exchanger, units have 4½ & 3.5" Mutators, chrome plated nickel
tubes, (3)20 HP V-Belt drives, these are designed for water in the
jacket, all have 3.5" diameter shafts, 3/60/230/460/1725 RPM, shafts
are in center of tube, stainless steel scrapers, 2" Tri Clamp
fittings, last used to make cake frosting. |
|
33972p- |
Cherry
Burrell, Thermutator model 6"x72", sweep surface heat exchanger, 9
square feet transfer surface per tube, 2 tubes, Units have 4½ & 3.5"
Mutators, chrome plated nickel tubes, 20HP V Belt drives, these are
designed for water in the jacket. |
|
17257p- |
Cherry
Burrell, Thermutator model 6"x72"DE, (1) barrel, model 6" x 72"DE,
460 volts, 20 HP, ammonia refrigeration, 2" inlet & outlet with a 3"
reducer, solid dasher type for 4 blades but have no blades, |
|
25387- |
Cherry
Burrell, Thermutator model 624L, 6"x26" stainless steel barrel,
products rated for 400 PSI at 400°F., mounted on mild steel frame.
(missing dasher) |
|
12991p- |
Cherry
Burrell, Thermutator model 672DE, direct expansion, stainless steel,
6'l long barrel, 9.0 square foot heat transfer, 10 HP. |
|
37357p- |
Cherry
Burrell, Thermutator model DE672 |
|
45392p- |
Cherry
Burrell, Thermutator Scraped Surface Heat Exchanger model 624L
double stacked includes (2) 6"x24" exchangers H steel cabinet ASME
UM certification chrome nickel tube stainless steel scrapers rotary
mechanical seal narrow clearance mutator 5 HP v-belt drive 2" ports
sanitary connections spare parts included 400 PSI at 400º F last
used Ethylene Glycol solution for cooling |
|
40419- |
Cherry
Burrell, Votator 6"x24", double, glycol, 5 HP. |
|
40420- |
Cherry
Burrell, Votator 6"x24", single, steam, Thermutator. |
|
45364p- |
Cherry
Burrell, Votator Scraped Surface Heat Exchanger model 35955VA 20 HP
drive shell MAWP 400 PSI at 375º F jacket MAWP 150 PSI at 375º F 14"
diameter barrel 147" long |
|
41184p |
Contherm,
6x9 Scraped Surface Heat Exchanger |
|
40382- |
Contherm,
stainless steel Votator 6"x72", single barrel, 9 square foot,
vertical heat exchanger, scraped surface. |
|
37527p- |
Crepaco,
Scraped Surface Heat Exchanger model 6x72 (3 tube) 20 HP electric
motor drives, last used on peanut butter, steam fitted, stators are
5-3/8" in diameter with stainless steel scraper blades, stainless
steel tubes |
|
45141- |
Crepaco,
Scraped Surface Heat Exchanger model HP2-799-S 2 barrel 6"x6' steam
10 HP |
|
43744p- |
Crepaco,
Scraped Surface Thermutator three barrels 1.5" inlet and outlet each
barrel 6" inside diameter x approximately 24" long (each barrel)
driven by Louis Allis mech variable speed drive 3 HP 230/460 volt
86-520 RPM unit is equipped with a Tecumseh 7.5 HP refrigeration
unit mounted above the machine R-12 refrigerant |
|
33898p- |
Crepaco,
side scraped surface heat exchanger (votator), (2)8"x60" chambers,
each is national board rated at 150 PSI at 200F. Each chamber driven
by a 30 HP 1170 RPM motor, 230/460 volt. Each chamber has 10½ square
feet of heat exchange surface. |
|
40425- |
Crepaco,
stainless steel Votator 6"x48", triple, ammonia, 10 HP. |
|
12993p- |
Crepaco,
Sweep Surface Heat Exchanger model HPI-365P, stainless steel,
6"x72", steam, 7½ HP, used primarily for ice cream |
|
45253- |
De Laval,
Contherm Vertical Scraped Surface Heat Exchanger model 6X9 HC-NCC
hydraulic rotor lift system less pore unit stainless steel cast
products heads nickel hard chrome plated cylinder coiled media
annulus 7.5 HP V-Belt drive product rating 450 PSI at 315º F |
|
44945p- |
De Laval,
Contherm Vertical Scraped Surface Heat Exchanger, model 6X9 HC-NCC
with hydraulic root lift system less power unit stainless steel cast
product heads nickel hard chrome plated cylinder coiled media
annulus 7.5 HP V-belt drive product rating 450 PSI at 315º C media
rating 225 at 315º C |
|
40412p- |
De Laval,
stainless steel Votator 6"x72", single, steam, 10 HP V-belt drive,
CIP barrels are rated at 450 PSI at 315° C., jacket rated for 225
PSI, last used for fruit juice, exterior of barrel is stainless
steel, interior is nickel clad, blades are plastic & units are
horizontal. |
|
40371- |
De Laval,
stainless steel Votator 6"x72", single, vertical, 7½ HP. |
|
40417- |
Girdler,
single Votator 14"x48", steam, 5 HP. |
|
40426- |
Girdler,
stainless steel Votator 6"x48", triple, ammonia, 25 HP. |
|
40385p- |
Girdler,
stainless steel Votator 6"x72", triple, steam, 25 HP motor to belt
drives, last used tomato paste, tubes are rated for 400 PSI at 400°
F., jackets rated for 150 PSI at 400° F., tubes serial numbers are
A501, A506 & A505. |
|
40384p- |
Girdler,
stainless steel Votator model FV183W, 6"x72", double barrel, steam,
25 HP, last used on tomato paste, driven by single 25 HP motor to
belt drives, tubes rated for 400 PSI at 400° F., jacket rated for
150 PSI at 400° F. Tubes serial number A444 & A437. |
|
40399- |
Girdler,
Votator 10"x60", single, stainless steel, steam, 7½ HP, 10" diameter
x 5' long, single carbon steel jacket, rated at 250 PSI at 375
internal & 150 PSI at 375 jacket, vari speed drive, 420-140 RPM. |
|
45418p- |
Girdler,
Votator Shortening System "A" unit is model S51F with 6" diameter x
24" long single Barrel driven by 10 HP motor and V-belt, "B" unit is
model 41553 with 6" diameter x 42" long twin barrels driven by a 10
HP motor and reducer refrigeration compressor is Carrier model
5H40-149 rated 235 PSI at 300º F driven by 20 HP motor |
|
45417p- |
Girdler,
Votator Shortening System model SK182-F with twin girdler votators
6"x72" unit includes 25 HP main motor drive for "A" unit and twin
barrel "B" units votators rated at 400 PSI internal 150 PSI on
jacket last run ammonia |
|
40386- |
Groen,
Scraped Surface Votator, vertical heat exchanger, 8"diameter
stainless steel cylinder 36"high, cylinder jacketed for 150PSI
at366ºF, 250 PSI at 115ºF, 10HP vari volume power pack, transfer
cylinder, hydraulic power pack, control panel, temperature
controller, rotor RPM indicator & product inlet temperature gauge
are mounted on a stainless steel portable stand |
|
44243p- |
Ole
Gerstenberg, Tubular Scrape Surface Heat Exchanger vertical cylinder
maximum pressure 3 Bar maximum working temperature 144º C stainless
steel construction. |
|
40416- |
Rossi &
Catelli, Twin Votator 12"x60", stainless steel, jacket, 10 HP. |
|
13693p- |
Single
Tube stainless steel Votator, Laboratory size, 5" diameter x11.5"
long, mounted on base with drive direct connected 1HP 3/60/220/460
vari speed drive, range is 156-780 RPM's, unit has base, motor
starter, plug in cord, unit has pins extending from shaft for
mixing, pins are 3/4" long & are 3/4" in center to center, work area
is 3" diameter, unit is not jacketed. Overall size 4' long x 3' high
x 14" wide. |
|
37524- |
St. Regis
Crepaco, Scraped Surface Heat Exchanger/ Plasticizer, stainless
steel product contact. |
|
42134- |
Struthers
Wells, Caustic Refining/Mixing System 12,000 pounds per hour
capacity vertical each with 10" x 62" static mixing barrels with
internal porcupine mixing element with plate baffles jacketed with a
7-1/2 HP variable speed top mounted drive on each and each with 112"
x 54" mixing barrel with a porcupine internal mixing element with
static plates equipped with a 10 HP directly connected gear head
motor drive electrical control panel system |
|
40387p- |
Votator
(2) stainless steel Chrome plated barrels, 6"x72" model FV 2A, The
unit is set up for direct expansion ammonia, rated 250 PSI internal,
150 PSI on jacket, one barrel is equipped with a 7½ HP gear head
motor drive, The second with a 10 HP drive. |
|
37528- |
Votator
Scrape Surface Heat Exchanger model 1C624L, 6"x24" tube, 5 HP
variable speed motor, chrome tube with 3" diameter stator |
|
37529- |
Votator
Scrape Surface Heat Exchanger model 6"x72" DE, stator is
approximately 4¾" in diameter, stainless steel product contact,
direct expansion capability, 7.5 HP 220/440 volt 3 phase motor,
chrome tube looks okay but some minor flaking on the discharge end |
|
35759- |
Votator
Scrape Surface Heat Exchanger model X1D, all stainless steel contact
parts, all XP, with 3'inside diameter tube & 2" shaft with dual
scraper, 2HP vari drive on votator, 220/440, 3phase has complete
controls, tachometer, steam traps, temperature controls & recorder
unit, skid mounted. |
|
43043- |
Votator,
4" diameter x 48" long chrome barrels. |
|
13694p- |
Votator,
4" diameter x 48" long, (2) tube unit, complete with drives &
piping. It has chrome barrels with mixing pins on 1 barrel &
processing blades on the 2nd barrel. The unit was last used to make
marshmallows. Includes stainless steel housing drive is V belt with
Reliance 25 HP 3/60/230/460 drip proof motor, frame T423, designed
for glycol or water cooling. |
|
42038p- |
Votator,
Laboratory Scraped Surface Heat Exchanger model 1C312L features all
stainless steel wetted parts 3" diameter x 12" jacketed tube with
2.25" diameter mutator shaft with dual full length stainless steel
removable scraper blades 50" exchanger inlet and outlet with NPT
connections U.S. Motors 2 HP variable speed drive 200-230/460 volt 3
phase directly coupled to mutator shaft with speed form 88.8 to 888
RPM mounted on factory base with painted exterior |
|
44258p- |
Votator,
Swept Surface Heat Exchanger model 6X24/1C624A 5 HP national board
#3239 pressurized seals bottom barrel has a 3 HP variable speed
motor and the top section is a holding tube/conditioner stainless
steel product contact |
|
|
